TIPS & EXPERT ADVICE ON ESSAYS, PAPERS & COLLEGE APPLICATIONS

The aim of this assessment is to investigate the factors that will affect the resistance of a length of resistance wire. Factors Length of wire  Thickness of wire  Temperature-We can’t do this factor because it is very hard to control and measure, also the resistance doesn’t change until the wire gets red hot. Type of wire-The school only has two types of wires, Constanton and Nickrome, we haven’t got a good selection of wires to choose from so we can’t do this factor. Method for Length To calculate the resistance, We are using the equation; A R=V A.

To start of with, you set up the equipment as shown in the diagram.  Check that the circuit is in working order by putting a resistor in that you know the resistance of, and use the equation to calculate the resistance.  The resistance wire is to be cut at 50cm.  Take the readings off the Volt and Amp metres.  Record results in an appropriate results table.  Repeat once more with a fresh piece of wire, so you can take an average.  Do a minimum of seven different lengths, using the same wire withn the same thickness. Method for Thickness A V  To start of with, you set up the equipment as shown in the diagram.

We Will Write a Custom Essay Specifically
For You For Only \$13.90/page!

order now

Check that the circuit is in working order by putting a resistor in that you know the resistance of, and use the equation to calculate the resistance. The resistance wire is to be cut at 40cm.Take the readings off the Volt and Amp metres.  Record results in an appropriate results table.  Repeat once more with a fresh piece of wire, so you can take an average.  Do a minimum of seven different thicknesses, using the same type of wire. Theory of Electricity An Atom is composed of positively charged particles and much smaller negatively charged particles called electrons.

The protons form the center of the atom, while the electrons whirl in an orbit around the proton center, much likes the moon orbits around the earth. If there were multiple earths very close together, and they each had a moon, they could play a game of catch, passing the moons from one earth’s orbit into the next earth’s orbit. But the laws of our game require that each earth has one moon in orbit around it. If an earth didn’t have a moon in orbit, having just passed it, it would have a positive charge on it, and desires to have a moon.

If an earth had an extra moon, having just caught one, it would have a negative charge to it, desiring to repel the extra moon. The passing of moons would continue until all earth’s again had one moon in orbit. CurrentThe flow of electricity in a wire is like this passing of moons. A wire is made out of a material called a conductor. A conductor is a material that likes to play this game of musical chairs. Wires are covered with materials called insulators, because insulators don’t like to play this game. That keeps passing electrons inside the wire.

When electrons are passed form an atom; they leave a “hole. ” Holes are potential receptors from other atoms and give the atom a positive charge that attracts negatively charged electrons form other atoms. This flow of electrons form one atom to the next is what we call “electricity. ” The flow of electricity is more properly called “current flow,” or simply “current. ” Current is the workhorse of electrical theory. The flow of electrons is what actually produces the power that we consume from the wall socket. “Voltage” is the pressure on the electrons to move form atom to atom.

Voltage sits in the wall socket waiting to move electrons, but is only the “potential” for work. If you don’t plug anything into the wall socket, voltage can’t do anything for you. But when you do plug something in, voltage determines how fast those electrons will come streaming out, and consequently how much current will flow; and how much power can be consumed. Resistance We are about to put the final piece of the puzzle together – resistance. Resistance “impedes” the flow of electrons. Resistance and impedance are related, but for now we are only concerned with resistance.

Resistance is measured in ohms. A light bulb has resistance. The filament resists the flow of electricity, and glows white hot in doing so. The resistance causes the bulb to only allow a portion of the current available in the wall socket, to flow out. A 100-watt light bulb uses more electricity from the wall than a 60-watt light bulb because the filament in a 100-watt bulb has less resistance to it. This lower resistance allows more current to flow through the bulb, consuming more power, producing more work and making more light. This work, by the way, is called “Wattage.

” If you multiply the voltage times the current answer is in watts. Prediction for length I predict that when the length of the conductor, in this case constantan, is increased, the electrical resistance will subsequently increase. This means that the resistance is directly proportional to the length. For example, when the length is doubled, the resistance is doubled, and when the length is tripled, the resistance is tripled. Therefore, by taking 3 lengths of 10cm wire and putting them in series, one by one, the resistance of the circuit should, at first, double, and then triple.

Total Resistance = Resistance1 + Resistance2 + Resistance3 Total Resistance = 3 x Resistance This shows that the resistance is directly proportional to the length. This may happen because; a conductor is made up of a lattice of atoms surrounded by a sea of free electrons (found in the outer shell of the constantan atoms. ) The free electrons jump from atom to atom and form the net flow of electrons around a circuit. Before a power supply is switched on, the free electrons are simply bouncing around inside the conductor. 